金属表面强化公司

With our all heart offer full Set of Brush plating Technique to customers

The brush plating technique has been used widely for product repairing,protection and decoration in the industrial areas of machinery electron、power station、transportation、metallurgy、textile and petrochemistry. Its characterization as following:

1.High deposition speed that is about 5～50times higher than that of deposition by bath;

2.The operation can be easily made at worksite and local plating deposition can be made for the workpieces without disassembling them from the main equipment;

3.Repairing work can be did for the bore-like and axle-like workpiece to remedy the friction loss or over-tolerance in size, because that the accurate plating deposition can be realized by controlling deposition thickness;

4.Adhesive strength between coat and substrate is high; the coat has dense crystal, low porosity, high hardness and high wear-and corrosion-resistances;

5.Plating operation at normal temperature, there are no phase transformation and no deformation occurring in coated work piece;

6.The equipment is simple and flexible to operate;

7.There are many kinds of plating solution for choice, and the pollution may be limited;

8.Lower investment、cost and risk, and high efficiency, benefit are advantages of this process。

The full set brush plating technique includes:

(A) Brush plating power source

1. A series of MPB system developed brush plating power source is controlled by computer, its feature as follows:

(1)By using advanced integrated chips, the equipment has high accuracy、stable and reliable performance, and better reappearance;

(2)By using Holl sensor,the equipment has accurate digital display, reliable gathering date property and linearity, the brush plating coat thickness of 0.1mm has an accuracy of 0.1±0.005mm;

(3)The equipment has a large capacity. The preset can be set optionally in the range of 0～99999.999A.H;

(4)A touching key board is used to make the equipment easy to operate. The equipment can continuously work under full load without noise and the life of its change-over switch is up to 2500 thousands times;

(5)The equipment is small、light、good look、easy to carry,maintance convenient and functions completeness.

The equipment specification as appendix.1

2. Other type of power source can also be provided to the custom’s order.

(B)Materials(Series Brush plating solutions):

Type	Brush plating solutions	Features
Solution for Pretreatment	Electrolytic Cleaning solution A series of activator
Cu-plating solution	Basic Cu-plating solution Acid Cu- plating solution Brass Cu- plating solution	Controllable hardness HV130～200 with excellent adhesive strength
Ni-plating solution	Series of acid Ni-plating solution	Controllable hardness HV350～520 with Good wear-and corrosion- Resistances and Excellent adhesive strength
	Series of basic Ni- plating solution
	Ni-P alloy- plating solution
Other plating solution	High efficiency Cr- plating solution Bright Ag- plating solution Au- plating solution Babbitt Metal High speed Zn- plating solution In-brush plating solution Series of high speed filling plating solution	excellent reducing friction

Note:About 100 kinds of brush plating solution with different functions can be provided,in which containing frequently used the solution for pretreatment、function and decoration plating.

As shown appendix 2.

(C)Auxiliary tools

Permanent multi-function plating pen,different kinds of anode,package sleeve and pump. as appendix3

(D)Besides the items mentioned above,the full set of brush plating technique also includes technical advice and personnel training.

Wuhan Research Institute of Material Protection

Address：126 Bao Feng Er Lu,Wuhan,P.R.China

Zip code：430030

Tel：027-83641667(O) 027-83640570(Bin’s home)

027-83612172(Peng’s home)

Fax：027-83637647

Connector(s) Bin Shengwu(Res.Fellow)

Peng Xiang(Senior engineer)

1、Appendix 1,

Brush plating equipment specification

Type	Available for	Factory price (U.S)＄
MBP-60A	The work piece with bore and outer diameter size Of less than 150mm and the plane Area of less than 10dm²	＄6,000/Set
MBP-100A	The work piece with bore and outer diameter size Of less than 300mm and the plane area Of less than 15dm2	＄8,000/Set
MBP-200A	The work piece with bore and outer diameter size Of less than 500mm and the plane Area of less than 30dm2	＄10,000/Set

　□ The equipments auxiliary tools and solutions for full set brush plating technology

返回主页